DEGISN OF A CHARGING SYSTEM USING AN ALTERNATOR TO SUPPORT THE PERFORMANCE OF THE REGENERATIVE BREAK SISTEM IN ELECTRIC VEHICLE

M. Arif Ma’sum; Ni Wayan Wardani; Debora Hotnauli Silaen

doi:10.56327/ijiscs.v8i2.1745

DEGISN OF A CHARGING SYSTEM USING AN ALTERNATOR TO SUPPORT THE PERFORMANCE OF THE REGENERATIVE BREAK SISTEM IN ELECTRIC VEHICLE

M. Arif Ma’sum⁽¹⁾, Ni Wayan Wardani⁽²⁾, Debora Hotnauli Silaen⁽³⁾,

(1) Department of Electrical Engineering, Udayana University, Bali
(2) Department of Electrical Engineering, Udayana University, Bali
(3) Department of Electrical Engineering, Udayana University, Bali

Corresponding Author

Abstract

The use of electric vehicles is now supported by a braking system capable of absorbing energy wasted from the braking process, known as regenerative brake. This research aims to optimize the use of the regenerative brake system by adding an alternator as a power generator to achieve more optimal charging. The voltage magnitude in the testing of the electric motorcycle NIU GOVA 03 obtained a generation voltage of 26VDC when traveling downhill for 100 meters at a speed of 45km/h. After designing the alternator for the electric motorcycle, the generation output increased to meet the battery charging voltage specification of 74VDC, suitable for application as a power source for a battery with a capacity of 60V14.7Ah. The braking portion before using the regenerative brake system over a distance of 100 meters took 4.8 seconds, but after implementing the regenerative brake system, the time decreased to 5.1 seconds. This indicates that the regenerative brake system, coupled with the alternator, can provide an effect in the form of decelerating the electric motorcycle by 8.7%.

Keywords

Regenerative Break, Electrical Energy, Electrical Vehicle

References

Aji, P., Primartadi, A., & Suyitno, S. Menentukan Kapasitas Motor Brushless Direct Current sebagai Penggerak Mobil Listrik. Auto Tech: Jurnal Pendidikan Teknik Otomotif Universitas Muhammadiyah Purworejo, 16(1), 7-13.

B. Prasetijo, H., Ropiudin, R., Dharmawan, “Generator Magnet Permanen Sebagai Pembangkit Listrik Putaran Rendah,” Ilm. Din. Rekayasa, vol. 8, pp. 70–77, 2016.

Clarissa Amelia Sitorus, Yono Hadi Pramono., 2017, Pembuatan Alternator Axial Flux

Coreless Dengan Menggunakan Magnet Permanen, Jurnal Teknik ITS Vol. 6, No. 2.

Dwifa, M. Beny., Munadi., 2015. Pengujian Efisiensi Energi Motor BLDC 72 Volt – 7 kW untuk Aplikasi Model Electric Urban Car. Jurnal Laboratorium Komputasi dan Otomasi: 1,

Immawan Insani, G. N. (2020). PERENCANAAN MOTOR LISTRIK BLDC TIPE HUB 1000W UNTUK PENGGGERAK SEPEDA MOTOR.

Muharam M. (2018). Analisis Tegangan keluaran Alternator Mobil Sebagai Pembangkit Energi Listrik Alternatif. RELE: Rekayasa Elektrikal dan Energi Jurnal Teknik Elektro Jurnal Teknik Elektro

Perdana, P. B., & Sutantra, I. N. (2018). Analisa penggunaan regenerative brake pada Mobil Multiguna pedesaan bertenaga listrik. Jurnal ITS, 7(1), E17-E20 in Automotive Technology, 149-163

Prasetyo, Aji., Priimartadi, Aci., Suyitno., 2021, Menentukan Kapasitas Motor Brushless Direct Current sebagai Penggerak Mobil Listrik. Jurnal Pendidikan Teknik Otomotif, FKIP, 16(1): 2623-2502.

Ramdhany, D. G., Hiron, N., & Busaeri, N. (2021). Modifikasi Motor Brushless Dc Menjadi Generator Sinkron Magnet Permanen Fluks Radial Putaran Rendah. Journal of Energy and Electrical Engineering (JEEE), 3(1).

Sulistyanto, Dwi. 2008. “Rancang Bangun Sepeda Listrik Menggunakan Sistem Portable” (Skripsi). Jakarta: Universitas Mercu Buana.

Viantama, I., & Suyitno, B. M. (2021). Analisis Perbandingan Sistem Kinerja Motor Penggerak Pada Mobil Listrik Kapasitas 75 kWh. Jurnal Asiimetrik: Jurnal Ilmiah Rekayasa Dan Inovasi, 157-164.

Full Text: PDF